Size guide
Ring Sizing Guide
1. easure an Existing Ring
-Place a ring that fits the intended finger comfortably on a flat surface.
-Measure straight across the widest part of the inside of the ring.
-Measure only the inner diameter, excluding the thickness of the band, and compare it with the diameter listed for each size option.
2. Measure with Paper or String
-Wrap a narrow strip of paper or a non-stretch string around the widest part of your finger.
-Make sure it is neither too tight nor too loose, then mark where the ends meet.
-Lay it flat and measure the marked length in millimeters.
-Measurements taken with paper or string may vary slightly and should be used as a guide only.
※Size Measurements
KR 7 / JP 7 / US 4 / EU 47
Inner Ø 15.0 mm / Finger Circ. approx. 50 mm
KR 8 / JP 8 / US 4.5 / EU 48
Inner Ø 15.3 mm / Finger Circ. approx. 51 mm
KR 9 / JP 9 / US 5 / EU 49
Inner Ø 15.7 mm / Finger Circ. approx. 52 mm
KR 10 / JP 10 / US 5.5 / EU 50
Inner Ø 16.0 mm / Finger Circ. approx. 53 mm
KR 11 / JP 11 / US 5.75–6 / EU 51
Inner Ø 16.3 mm / Finger Circ. approx. 54 mm
KR 12 / JP 12 / US 6–6.25 / EU 52
Inner Ø 16.7 mm / Finger Circ. approx. 55 mm
KR 13 / JP 13 / US 6.5 / EU 53
Inner Ø 17.0 mm / Finger Circ. approx. 56 mm
KR 14 / JP 14 / US 7 / EU 54
Inner Ø 17.3 mm / Finger Circ. approx. 57 mm
KR 15 / JP 15 / US 7.5 / EU 55–56
Inner Ø 17.7 mm / Finger Circ. approx. 58 mm
※ International size conversions may vary by country and brand. For the most accurate fit, please refer to the inner diameter listed for each size option.
※ Custom sizes are available upon request. Select Custom Size and enter your preferred ring size in the order notes.
Bracelet Sizing Guide
-Measure your wrist circumference using a measuring tape or a strip of paper about 1 cm wide, placed around the position where the bracelet will sit.
-If you prefer a slightly looser fit, we recommend adding approximately 1 cm to your measured wrist size.
-Compare your wrist measurement to the total length (Length) indicated on each product page to choose the most suitable size.
-Due to the nature of handcrafted production, slight variations may occur from piece to piece.
Necklace Sizing Guide
1. Using thread or a thin string
-Wrap the thread lightly around your neck at the position where you’d like the necklace to sit.
-Pinch the point where the ends meet.
-Lay the thread flat and measure it with a ruler to find your worn length.
2. Using a paper strip
-Cut a long strip of paper about 1–2 cm wide and wrap it around your neck.
-Mark where the ends meet, then lay it flat and measure the distance.
-Paper provides a firmer, more accurate measurement than thread.
3. Measuring an existing necklace
-Lay your necklace flat and measure from end to end, including the clasp.
-This method is the most accurate if you already know your preferred fit.
Additional Notes
-Light and Shade lists sizes based on the actual worn length, including the clasp.
-Fit may vary slightly depending on the chain structure and overall design.
-If you are between sizes, we recommend opting for the slightly longer option.
